Call

 

We've stumbled on this article about A Step-by-Step Guide to Installing a Bathtub below on the web and believe it made good sense to discuss it with you on this site.

Installing a tub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is also a moderately challenging project. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as set in the new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to consider utilizing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly help you install a new tub in your bathroom if you have actually currently acquired a brand-new bathtub and also don't need to change the arrangement of your previous supply of water pipelines.
Your tools and material list ought to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Bathtub

Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub until the spirit level reviews degree.
To install faucets, fit the bottom of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the supply of water and examine all joints and also new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as also examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait until the tub has actually been used at the very least when as this will settle it right into its last position.

 

 

Getting ready for the Installment

Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final position.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall surface between the bath as well as the tiling, causing complications with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I hope you enjoyed reading our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking a few minutes to read through our article. Those who enjoyed our post plz be sure to share it. Thank you for taking the time to read it.

Ring, relax, resolved!